Moving Sale! Call 410-925-7701 or email inquiry@redbeardsailing.com for details

How to Set Up Your Takacat

All Posts
How to Set Up Your Takacat

No matter what you'll be using your new Takacat for, we want to ensure you get out on the water as soon as possible and do it safely.

Below is an easy-to-follow set-up guide for the Takacat Lite X, as well as two video tutorials.

If you'd like to download the Takacat Owner's Manual, click here.

Tools You'll Need:

  • An air pump with a standard Halkey-Roberts valve. A hand pump is included with your Takacat.
  • A small container of soapy water (optional)
  • Deflated Takacat Lite X and its parts

Instructions for Setting Up Your Takacat Lite X

1) Unfold and lay out the boat hull tubes.

Rolled Up Takacat Lite X

2) Locate the inflator valve at the rear of the hulls and inflate to 3 psi with the included hand pump or optional electric pump.

Inflating Takacat Lite X with Hand Pump

3) From the rear, insert the lower transom bar into the lower set of tubes on the boat hulls.

    • Lubricate the tube beforehand with soapy water as this will make sliding the transom bars into place much easier. If you don't have soap handy, spit or just plain water will work in a pinch.
    • The stainless tab should be facing up when it's installed properly.

    Takacat Lite X Lower Transom Bar Set-Up

    5) Attach black velcro straps around the tube transom.

    • The black flaps should go over the lower bar and velcro back to itself.

    Takacat Lite X Lower Transom Bar with Velcro Straps

    6) From the front, insert the upper transom bar into the upper set of tubes on the boat hulls.

    • Like with the lower transom, lubricate the tubes with a bit of soapy water.
    • The stainless tab should be facing down when it's installed properly.

    Takacat Lite X Upper Transom Bar Set-Up

    7) Slot the smaller motor mount board inside the tube transom.

    Takacat Lite X Motor Mount Board

    8) Creating a sandwich, assemble the rest of the transom.

    • The bolt passes from the rear to the front with the rubber washer between the wooden motor mount boards.
    • Proper sandwich order below:
      Bolt | SS Washer | Back Board | Rubber Washer | Front Board | SS Washer | Hand Nut
    • The nut should be hand-tightened only.

    Special note: Omitting the rubber spacer could cause catastrophic failure of the outboard bracket potentially causing an unwanted outboard donation to Davy Jones' Locker.

    Takacat Lite X Motor Mount Installed

     9) Unfold and place the air deck floor between tubes.

    • There is no need to get it perfectly under each hull tube, but the rear of the floor should be flush with the lower transom bar.

    Takacat Lite X Inflatable Floor Installation

    10) Insert D-Rings, on the bottom of the air deck floor, through the slots in the
    boat floor fabric layer.

    Takacat Lite X D Rings

    11) Install the bow support straps.

    Takacat Lite X D Rings Secured

    12) Inflate the air deck floor to 10psi / 65kpa (electric pump) via its bow located Halkey-Roberts valve.

    • While inflating be sure to pause and walk on the floor to push
      it into place.
    • Don't forget to activate the check valve by pressing down on the center pin and turning it a 1/4-turn in either direction.
    • If it is popped up, it won't let any air escape.

    Fully Inflated Takacat Lite X Floor

    13) Inflate the float seat.

    • The seat can be inflated to a pressure that is most comfortable.
    • The seat is designed for comfortable rowing, and can also be used as a throwable flotation device.

    Takacat Float Seat

    14) Assemble each oar and install.

    • Be sure to attach retaining nut to prevent losing oars when in use.

    Takacat Lite X Oar Lock

    15) If you opted for the Quick Release Beach Wheels, install them now in the down position.

    • When in the down position, the wheels provide enough height to mount a 15" short shaft outboard in the upright position.
    • Wheels are side specific, make sure to mount them with tires facing inward
      when in the down position to prevent friction damage to the boat hulls.

    Takacat Lite X Quick Release Wheels in Down Position

    16) If you opted for the Quick Release Rod Holders, install them now into the upper transom bar.

    Takacat Lite X Quick Release Rod Holder Set

    17) Fit outboard motor, if applicable.

    18) After launching your boat into the water, check the pressure in the hulls to verify you still have 3 psi hull air pressure.

    • If the water is cooler than the surrounding air temperature the air inside the hulls will condense causing a pressure drop.
    • Use the manual pump to re-inflate to 3 psi hull air pressure.

    19) Enjoy your new Takacat and leave a review on Red Beard Sailing's website to let us know how you're enjoying your new boat!

     

    When you are finished using your Takacat and are ready to put it away, check out our Pack Away Instructions.

    Red Beard Sailing No Thanks